修复Metus Jog运动错误

HSI_HexagonMI_EF3/HSI.h

@@ -323,7 +323,7 @@ enum HSI_MOTION_TYPE
 enum HSI_MOTION_AXIS_TYPE
 {
 	HSI_MOTION_AXIS_X = 0x0001,// This is the default "Sensor level" X Axis - use on single X axis machines
-	HSI_MOTION_AXIS_Y = 0x0000,// This is the default "Sensor level" Y Axis - use on single Y axis machines
+	HSI_MOTION_AXIS_Y = 0x0002,// This is the default "Sensor level" Y Axis - use on single Y axis machines
 	HSI_MOTION_AXIS_Z = 0x0004,// This is the default "Sensor level" Z Axis - use on single Z axis machines
 	HSI_MOTION_AXIS_R = 0x0008,// This is the default "Sensor level" R Axis - use on single R axis machines
 	HSI_MOTION_AXIS_X1 = 0x0010,// This is the 1st X Axis - use on multiple axis machines when specific axis needed

HSI_HexagonMI_EF3/HSI_HexagonMI_EF3.vcxproj

@@ -107,7 +107,7 @@
     </Link>
     <PostBuildEvent>
       <Command>copy "$(TargetDir)$(ProjectName).dll" "$(SolutionDir)HSI_SEVENOCEAN_EF1_CsTest\bin\Debug\HSI.dll"
-copy "$(TargetDir)$(ProjectName).dll" "C:\Hexagon\Metus2021\HSI.dll"
+copy "$(TargetDir)$(ProjectName).dll" "C:\Hexagon\Metus2021\HSI_Sevenocean_EF3.dll"
 copy "$(TargetDir)$(ProjectName).dll" "E:\HexagonProjects\2022-05-直线电机平台\EF3-Interfac\PcDmis\Base\Interfac\Msi\Hsi\Tools\UsbUtility\HSI_Sevenocean_EF1_WPFTest\bin\x64\Debug\HSI.dll"</Command>
     </PostBuildEvent>
     <PreBuildEvent>

HSI_HexagonMI_EF3/HSI_Motion.cpp

@@ -428,6 +428,7 @@ HSI_STATUS HSI_Motion::Startup(HWND _hWnd, bool _bOfflineOnly)
 			{
 				//直线电机平台，采用串口通信，8个数据位，1个停止位，无奇偶校验，波特率256000
 				m_SO7_Serial.SetPort(m_EF3COMPort, 256000, 0, 8, 1, 0); //打开串口
+#ifndef OFFLINE
 				if (!m_SO7_Serial.Open()) //如果串口打开失败
 				{
 					g_pLogger->SendAndFlushWithTime(L"[Startup] m_SO7_Serial.Open is false,connected failed\n");
@@ -439,6 +440,9 @@ HSI_STATUS HSI_Motion::Startup(HWND _hWnd, bool _bOfflineOnly)
 					EventCallback(sEvenProp);
 					return HSI_STATUS_FAILED;
 				}
+#endif // OFFLINE
+
+		
 				m_SO7_Serial.SetTimeouts(1000, 1000);
 				m_bConnected = true;
 				g_pLogger->SendAndFlushWithTime(L"[Startup] Serial: [COM%d] is open success\n", m_EF3COMPort);
@@ -458,7 +462,10 @@ HSI_STATUS HSI_Motion::Startup(HWND _hWnd, bool _bOfflineOnly)
 				g_pLogger->SendAndFlushWithTime(L"[ACS Motion] In\n");
 				g_pLogger->SendAndFlushWithTime(
 					L"[ACS Motion] Wait for opening of communication with the controller... \n");
-
+				
+#ifdef OFFLINE //如果定义离线模式
+				handleACS = acsc_OpenCommSimulator();
+#else
 				// 10.0.0.100 - default IP address of the controller
 				handleACS = acsc_OpenCommEthernet("10.0.0.100", ACSC_SOCKET_DGRAM_PORT);
 				// for the connection to the controller via local network or Internet
@@ -477,7 +484,7 @@ HSI_STATUS HSI_Motion::Startup(HWND _hWnd, bool _bOfflineOnly)
 					EventCallback(sEvenProp);
 					return HSI_STATUS_FAILED;
 				}
-
+#endif
 				//使能电机
 				int Axes[] = { ACSC_AXIS_0, ACSC_AXIS_1, ACSC_AXIS_4, -1 };
 				if(!acsc_EnableM(handleACS, Axes,NULL))
@@ -1000,7 +1007,7 @@ HSI_STATUS HSI_Motion::HomeMachineOld(bool bHomed)
 		{
 			if (CurrentHomeMachineState == E_EF3_HOME_FINISHED)
 			{
-				byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));
+				byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes)); //HomeMachineOld
 				m_cSendData[0] = CT_MOTOR;
 				m_cSendData[1] = CT_MOTOR_SET;
 				m_cSendData[2] = AxisTypes;
@@ -1563,7 +1570,7 @@ HSI_STATUS HSI_Motion::JogOld(UINT AxisTypes, double Speed)
 		int DecCurve(1);
 		int JogSpeed(1);
 		bool bJOGDir = Speed > 0 ? true : false;
-		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));
+		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));//JogOld
 		jogAxisNum = AxisNumber;
 		jogDirFlag = bJOGDir;
 		m_Thread_State = HSI_THREAD_PAUSED;
@@ -1836,6 +1843,7 @@ HSI_STATUS HSI_Motion::JogOld(UINT AxisTypes, double Speed)
 HSI_STATUS HSI_Motion::Jog(UINT AxisTypes, double Speed)
 {
 	auto rStatus = HSI_STATUS_NORMAL;
+	g_pLogger->SendAndFlushWithTime(L"[Jog] aixs: [%d]  speed:[%d]\n", AxisTypes, Speed);
 	if (g_pHSI_Motion)
 	{
 		if (m_DeviceType != 3) //非转盘设备
@@ -1845,7 +1853,7 @@ HSI_STATUS HSI_Motion::Jog(UINT AxisTypes, double Speed)
 		}
 
 		bool bJOGDir = Speed > 0 ? true : false; //运动方向
-		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));
+		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));//Jog
 		jogAxisNum = AxisNumber;
 		jogDirFlag = bJOGDir;
 		m_Thread_State = HSI_THREAD_PAUSED;
@@ -1860,10 +1868,10 @@ HSI_STATUS HSI_Motion::Jog(UINT AxisTypes, double Speed)
 		}
 
 		//是否回过家
-		if (m_Home_Machine_Axis[AxisNumber] == 0)
+		//if (m_Home_Machine_Axis[AxisNumber] == 0)
-		{
+		//{
-			return rStatus;
+		//	return rStatus;
-		}
+		//}
 
 		// 是否启用急停
 		//if ((StartSpeed < 250) && (DriveSpeed < 6))
@@ -1880,14 +1888,15 @@ HSI_STATUS HSI_Motion::Jog(UINT AxisTypes, double Speed)
 
 		//开始JOG运动
 		int acsDirection = bJOGDir ? ACSC_POSITIVE_DIRECTION : ACSC_NEGATIVE_DIRECTION; //正方向，或 负方向
-		if (!acsc_Jog(handleACS, 0, AxisTypes, acsDirection, nullptr))
+		if (!acsc_Jog(handleACS, 0, jogAxisNum, acsDirection, nullptr))
 		{
-			g_pLogger->SendAndFlushWithTime(L"[Jog] [%d] Öá [%s] ·½ÏòÒƶ¯Ê§°Ü", AxisTypes, bJOGDir ? "Õý" : "¸º");
+			printf("[Jog] 轴[%d] [%s] 方向移动失败", AxisTypes, bJOGDir? "正" : "负");
+			g_pLogger->SendAndFlushWithTime(L"[Jog] aixs:[%d] JOGDir:[%s] Jog move failed\n", AxisTypes, bJOGDir ? "P" : "N");
 			ErrorsHandler();
 		}
 
 		jogMoving = true;
-		g_pLogger->SendAndFlushWithTime(L"[Jog] Out, bJOGDir = %s\n", bJOGDir ? "positive":"negative");
+		g_pLogger->SendAndFlushWithTime(L"[Jog] Out, bJOGDir = %s\n", bJOGDir? "positive":"negative");
 	}
 	return rStatus;
 }
@@ -1912,7 +1921,7 @@ HSI_STATUS HSI_Motion::JoyStick(UINT AxisTypes, long Speed)
 		int DecCurve(1);
 		int JogSpeed(1);
 		bool bJOGDir = Speed > 0 ? true : false;
-		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));
+		byte AxisNumber = static_cast<byte>(AxisConvertIndex(AxisTypes));//JoyStick
 		jogAxisNum = AxisNumber;
 		jogDirFlag = bJOGDir;
 		m_Thread_State = HSI_THREAD_PAUSED;
@@ -2246,7 +2255,7 @@ HSI_STATUS HSI_Motion::StopJog()
 	{
 		g_pLogger->SendAndFlushWithTime(L"[StopJog] In\n");
 		t_end = GetTickCount();
-		g_pLogger->SendAndFlushWithTime(L"[StopJog] t_start = %d, t_end = %d\n", t_start, t_end);
+		//g_pLogger->SendAndFlushWithTime(L"[StopJog] t_start = %d, t_end = %d\n", t_start, t_end);
 		jogMoving = false;
 		if (t_end - t_start < 100)
 		{
@@ -2297,6 +2306,7 @@ HSI_STATUS HSI_Motion::StopJog()
 	return rStatus;
 }
 
+
 //===========================================================================
 HSI_STATUS HSI_Motion::StopJogEx(UINT AxisTypes)
 {
@@ -6883,19 +6893,19 @@ short HSI_Motion::AxisConvertIndex(UINT AxisTypes)
 		}
 	case HSI_MOTION_AXIS_Y:
 		{
-			AxisNumber = 0x02;
+			AxisNumber = 0x00;
 			break;
 		}
 	case HSI_MOTION_AXIS_Z:
-		{
-			AxisNumber = 0x03;
-			break;
-		}
-	case HSI_MOTION_AXIS_R:
 		{
 			AxisNumber = 0x04;
 			break;
 		}
+	//case HSI_MOTION_AXIS_R:
+	//	{
+	//		AxisNumber = 0x04;
+	//		break;
+	//	}
 	default:
 		{
 			g_pLogger->SendAndFlushWithTime(L"AxisConvertIndex failed,AxisTypes = %d,AxisNumber = %d\n", AxisTypes,

HSI_HexagonMI_EF3/logger.cpp

@@ -84,7 +84,7 @@ void CLogger::SendAndFlushWithTime(LPCTSTR format, ...)
 		va_start(list, format);
 		length = vswprintf_s(m_Str2, 5000, format, list);
 		CTime _cTime = CTime::GetCurrentTime();
-		CString csTime = _cTime.Format("[%Y%m/%d %H:%M:%S");
+		CString csTime = _cTime.Format("[%Y/%m/%d %H:%M:%S");
 		struct _timeb timebuffer;
 		_ftime64_s(&timebuffer);
 		if (m_File)

HSI_HexagonMI_EF3/version.h

@@ -12,5 +12,5 @@
 #define HSI_VERSION_REVNUM              
 #define HSI_VERSION_BUILD_DATE        _T(__DATE__ )  
 #define HSI_VERSION_BUILD_TIME        _T(__TIME__ )  
-#define HSI_FILE_DESCRIPTION          "2022.10.20 / 12:06 "  
+#define HSI_FILE_DESCRIPTION          "2022.10.21 / 18:06 "  
-#define HSI_FILE_CSDESCRIPTION        _T("2022.10.20 / 12:06 ")  
+#define HSI_FILE_CSDESCRIPTION        _T("2022.10.21 / 18:06 ")  

HSI_SEVENOCEAN_EF1_CsTest/bin/Debug/Config/EF3_Motion.ini

@@ -1,343 +0,0 @@
-[JOG_SPEED]
-JOG速度(pulse/ms)
-JOG_SPEED_0=200.0
-JOG_SPEED_1=150.0
-JOG_SPEED_2=50
-JOG_SPEED_3=10
-JOG_SPEED_4=1
-
-;JOG加速度(pulse/ms^2)
-JOG_ACC_0=2.0
-JOG_ACC_1=2.0
-JOG_ACC_2=2.0
-JOG_ACC_3=1.0
-JOG_ACC_4=1.0
-
-;JOG减速度(pulse/ms^2)
-JOG_DEC_0=2.0
-JOG_DEC_1=2.0
-JOG_DEC_2=2.0
-JOG_DEC_3=1.0
-JOG_DEC_4=1.0
-
-;JOG模式采用急停还是平滑停止,0是平滑停止1为急停，默认0
-JOG_STOP_MODE_1=0
-JOG_STOP_MODE_2=0
-JOG_STOP_MODE_3=0
-JOG_STOP_MODE_4=0
-JOG_STOP_MODE_5=0
-JOG_STOP_MODE_6=0
-JOG_STOP_MODE_7=0
-JOG_STOP_MODE_8=0
-JOG_STOP_MODE=0
-JOG_SPEED_GEAR0_1=200.0
-JOG_ACC_GEAR0_1=2.0
-JOG_DEC_GEAR0_1=2.0
-JOG_SPEED_GEAR0_2=200.0
-JOG_ACC_GEAR0_2=2.0
-JOG_DEC_GEAR0_2=2.0
-JOG_SPEED_GEAR0_3=150.0
-JOG_ACC_GEAR0_3=2.0
-JOG_DEC_GEAR0_3=2.0
-JOG_SPEED_GEAR0_4=200.0
-JOG_ACC_GEAR0_4=2.0
-JOG_DEC_GEAR0_4=2.0
-JOG_SPEED_GEAR1_1=100.0
-JOG_ACC_GEAR1_1=2.0
-JOG_DEC_GEAR1_1=2.0
-JOG_SPEED_GEAR1_2=100.0
-JOG_ACC_GEAR1_2=2.0
-JOG_DEC_GEAR1_2=2.0
-JOG_SPEED_GEAR1_3=80.0
-JOG_ACC_GEAR1_3=2.0
-JOG_DEC_GEAR1_3=2.0
-JOG_SPEED_GEAR1_4=100.0
-JOG_ACC_GEAR1_4=2.0
-JOG_DEC_GEAR1_4=2.0
-JOG_SPEED_GEAR2_1=50.0
-JOG_ACC_GEAR2_1=2.0
-JOG_DEC_GEAR2_1=2.0
-JOG_SPEED_GEAR2_2=50.0
-JOG_ACC_GEAR2_2=2.0
-JOG_DEC_GEAR2_2=2.0
-JOG_SPEED_GEAR2_3=50.0
-JOG_ACC_GEAR2_3=2.0
-JOG_DEC_GEAR2_3=2.0
-JOG_SPEED_GEAR2_4=50.0
-JOG_ACC_GEAR2_4=2.0
-JOG_DEC_GEAR2_4=2.0
-JOG_SPEED_GEAR3_1=10.0
-JOG_ACC_GEAR3_1=1.0
-JOG_DEC_GEAR3_1=1.0
-JOG_SPEED_GEAR3_2=10.0
-JOG_ACC_GEAR3_2=1.0
-JOG_DEC_GEAR3_2=1.0
-JOG_SPEED_GEAR3_3=10.0
-JOG_ACC_GEAR3_3=1.0
-JOG_DEC_GEAR3_3=1.0
-JOG_SPEED_GEAR3_4=10.0
-JOG_ACC_GEAR3_4=1.0
-JOG_DEC_GEAR3_4=1.0
-JOG_SPEED_GEAR4_1=1.0
-JOG_ACC_GEAR4_1=1.0
-JOG_DEC_GEAR4_1=1.0
-JOG_SPEED_GEAR4_2=1.0
-JOG_ACC_GEAR4_2=1.0
-JOG_DEC_GEAR4_2=1.0
-JOG_SPEED_GEAR4_3=1.0
-JOG_ACC_GEAR4_3=1.0
-JOG_DEC_GEAR4_3=1.0
-JOG_SPEED_GEAR4_4=1.0
-JOG_ACC_GEAR4_4=1.0
-JOG_DEC_GEAR4_4=1.0
-
-;0:都使用(正常情况)   1:只使用灯，而不使用控制器;默认0
-[USE_LIGHT]
-ONLY_USE_LIGHT=0
-
-[RESOLUTION]
-;光栅尺的分辨率(mm)
-SCALE_RESOLUTION_1=0.0004
-SCALE_RESOLUTION_2=0.0004
-SCALE_RESOLUTION_3=0.0004
-SCALE_RESOLUTION_4=0.0004
-SCALE_RESOLUTION_5=0.0004
-SCALE_RESOLUTION_6=0.0004
-SCALE_RESOLUTION_7=0.0004
-SCALE_RESOLUTION_8=0.0004
-
-[LIMIT]
-;负限位(mm)，必须是负数
-;NEG_WORKING_LIMIT_1=-260.0
-;NEG_WORKING_LIMIT_2=-40.0
-;NEG_WORKING_LIMIT_3=-40.0
-NEG_WORKING_LIMIT_1=-1.0
-NEG_WORKING_LIMIT_2=-1.0
-NEG_WORKING_LIMIT_3=-1.0
-NEG_WORKING_LIMIT_4=-40.0
-NEG_WORKING_LIMIT_5=-40.0
-NEG_WORKING_LIMIT_6=-40.0
-NEG_WORKING_LIMIT_7=-40.0
-NEG_WORKING_LIMIT_8=-40.0
-
-;正限位(mm)，必须是正数
-;POS_WORKING_LIMIT_1=40.0
-;POS_WORKING_LIMIT_2=160.0
-;POS_WORKING_LIMIT_3=160.0
-POS_WORKING_LIMIT_1=500.0
-POS_WORKING_LIMIT_2=500.0
-POS_WORKING_LIMIT_3=250.0
-POS_WORKING_LIMIT_4=200.0
-POS_WORKING_LIMIT_5=200.0
-POS_WORKING_LIMIT_6=200.0
-POS_WORKING_LIMIT_7=200.0
-POS_WORKING_LIMIT_8=200.0
-
-[HOME]
-;选择需要回家的轴号，改为1
-HOME_MACHINE_AXIS_1=1
-HOME_MACHINE_AXIS_2=1
-HOME_MACHINE_AXIS_3=1
-HOME_MACHINE_AXIS_4=0
-HOME_MACHINE_AXIS_5=0
-HOME_MACHINE_AXIS_6=0
-HOME_MACHINE_AXIS_7=0
-HOME_MACHINE_AXIS_8=0
-
-;是否启动实际位置判断是否回家，默认0，1启用，0关闭
-IS_HOME_ENC_POS=0
-;是否启动规划位置判断是否回家，默认1，1启用，0关闭
-IS_HOME_PRF_POS=1
-
-;关闭电源时记住当前的位置，用于判断是否需要回家
-HOME_POS_AXIS_1=0
-HOME_POS_AXIS_2=0
-HOME_POS_AXIS_3=0
-HOME_POS_AXIS_4=0
-HOME_POS_AXIS_5=0
-HOME_POS_AXIS_6=0
-HOME_POS_AXIS_7=0
-HOME_POS_AXIS_8=0
-
-;回家第一段速度(pulse/ms)
-HOME_HIGH_SPEED_1=200.0
-HOME_HIGH_SPEED_2=200.0
-HOME_HIGH_SPEED_3=200.0
-HOME_HIGH_SPEED_4=200.0
-HOME_HIGH_SPEED_5=200.0
-HOME_HIGH_SPEED_6=200.0
-HOME_HIGH_SPEED_7=200.0
-HOME_HIGH_SPEED_8=200.0
-
-;回家第一段加速度(pulse/ms^2)
-HOME_HIGH_ACC_1=2.0
-HOME_HIGH_ACC_2=2.0
-HOME_HIGH_ACC_3=2.0
-HOME_HIGH_ACC_4=2.0
-HOME_HIGH_ACC_5=2.0
-HOME_HIGH_ACC_6=2.0
-HOME_HIGH_ACC_7=2.0
-HOME_HIGH_ACC_8=2.0
-
-;回家第二段速度(pulse/ms)
-HOME_LOW_SPEED_1=180.0
-HOME_LOW_SPEED_2=180.0
-HOME_LOW_SPEED_3=180.0
-HOME_LOW_SPEED_4=180.0
-HOME_LOW_SPEED_5=180.0
-HOME_LOW_SPEED_6=180.0
-HOME_LOW_SPEED_7=180.0
-HOME_LOW_SPEED_8=180.0
-
-;回家第二段加速度(pulse/ms^2)
-HOME_LOW_ACC_1=2.0
-HOME_LOW_ACC_2=2.0
-HOME_LOW_ACC_3=2.0
-HOME_LOW_ACC_4=2.0
-HOME_LOW_ACC_5=2.0
-HOME_LOW_ACC_6=2.0
-HOME_LOW_ACC_7=2.0
-HOME_LOW_ACC_8=2.0
-
-;回家延时时间(ms)
-HOME_TIME_1=1000
-HOME_TIME_2=1000
-HOME_TIME_3=1000
-HOME_TIME_4=1000
-HOME_TIME_5=1000
-HOME_TIME_6=1000
-HOME_TIME_7=1000
-HOME_TIME_8=1000
-
-[PID]
-;PID比例调节,应从0.01递增开始调试
-PID_KP_1=1.20
-PID_KP_2=1.20
-PID_KP_3=1.20
-PID_KP_4=1.20
-PID_KP_5=1.20
-PID_KP_6=1.20
-PID_KP_7=1.20
-PID_KP_8=1.20
-
-[PRECISION]
-;超时时间(0.1ms)
-PRECISION_TIME_1=20000
-PRECISION_TIME_2=20000
-PRECISION_TIME_3=20000
-PRECISION_TIME_4=20000
-PRECISION_TIME_5=20000
-PRECISION_TIME_6=20000
-PRECISION_TIME_7=20000
-PRECISION_TIME_8=20000
-
-;回家误差脉冲个数
-PRECISION_COUNT_1=8
-PRECISION_COUNT_2=8
-PRECISION_COUNT_3=8
-PRECISION_COUNT_4=8
-PRECISION_COUNT_5=8
-PRECISION_COUNT_6=8
-PRECISION_COUNT_7=8
-PRECISION_COUNT_8=8
-
-[SET_POSITION_SPEED]
-;XYZ定位的合成速度(pulse/ms)
-SET_POTION_SPEED_1=500.0
-SET_POTION_SPEED_2=500.0
-SET_POTION_SPEED_3=500.0
-SET_POTION_SPEED_4=500.0
-SET_POTION_SPEED_5=500.0
-SET_POTION_SPEED_6=500.0
-SET_POTION_SPEED_7=500.0
-SET_POTION_SPEED_8=500.0
-
-;XYZ定位的合成加速度(pulse/ms^2)
-SET_POTION_ACC_1=2.5
-SET_POTION_ACC_2=2.5
-SET_POTION_ACC_3=2.5
-SET_POTION_ACC_4=2.5
-SET_POTION_ACC_5=2.5
-SET_POTION_ACC_6=2.5
-SET_POTION_ACC_7=2.5
-SET_POTION_ACC_8=2.5
-
-;XYZ定位的终点速度(pulse/ms)
-SET_POTION_DEC_1=1.0
-SET_POTION_DEC_2=1.0
-SET_POTION_DEC_3=1.0
-SET_POTION_DEC_4=1.0
-SET_POTION_DEC_5=1.0
-SET_POTION_DEC_6=1.0
-SET_POTION_DEC_7=1.0
-SET_POTION_DEC_8=1.0
-
-;XYZ定到位判断次数
-SET_POSITION_COUNT_1=240
-SET_POSITION_COUNT_2=240
-SET_POSITION_COUNT_3=240
-SET_POSITION_COUNT_4=240
-SET_POSITION_COUNT_5=240
-SET_POSITION_COUNT_6=240
-SET_POSITION_COUNT_7=240
-SET_POSITION_COUNT_8=240
-
-[COMPORT]
-;灯光控制器类型选择
-;0:启用c++调用灯光,不使用STM32 USB控制时，需要把下面的IS_STM32_USB改为0
-;1:wpf直接调用;
-;2:DP光源控制器;
-;3:旧的6环8区为3(环形可调);
-;4:新的6环8区为4(扇区可调);
-;5:STM32控制器,IP地址在exe目录下的CameraNum.ini中修改
-;61:OPT光源控制器网络模式(111ms),IP地址在exe目录下的CameraNum.ini中修改，串口模式62(44ms);
-COM_PORT_CPP_WPF=0
-
-;使用stm32时，是否使用USB通讯，使用该功能时，COM_PORT_CPP_WPF必须等于0
-IS_STM32_USB=0
-
-;是否打开第一个串，1为打开，0为关闭，默认0
-IS_COM_PORT_A=0
-COM_PORT_A=2
-COM_PORT_A_LED_1=1
-COM_PORT_A_LED_2=1
-COM_PORT_A_LED_3=1
-COM_PORT_A_LED_4=1
-
-;是否打开第二个串，1为打开，0为关闭，默认0
-IS_COM_PORT_B=0
-COM_PORT_B=6
-COM_PORT_B_LED_1=1
-COM_PORT_B_LED_2=1
-COM_PORT_B_LED_3=1
-COM_PORT_B_LED_4=1
-
-[TRRIGER]
-;线性点触发的脉冲宽度
-LINEAR_PULSE_WIDTH=500
-
-;等间距触发的脉冲宽度
-INTERVAL_PULSE_WIDTH=500
-
-;手动触发
-HOLD_TIME=150
-
-[LOG]
-;是否打开记录，默认0为关闭，1位打开,;LOG_IS_OPEN_0为是否打开记录功能
-LOG_IS_OPEN_0=1
-LOG_IS_OPEN_1=1
-LOG_IS_OPEN_2=1
-LOG_IS_OPEN_3=1
-LOG_IS_OPEN_4=0
-LOG_IS_OPEN_5=0
-LOG_IS_OPEN_6=0
-LOG_IS_OPEN_7=0
-LOG_IS_OPEN_8=0
-;是否启用统计定位函数的时间日志，1：启用，默认0关闭
-LOG2_IS_OPEN=0
-;定位几次后，计算这几次总共用时mm，默认4次
-LOG_SUM_COUNT=0
-
-
-
-